สินค้า

For indoor use ● Typically used for heavy duty applications ● Among the strongest Pan-Ty ® Cable Tie available ● Can be used with MCEH mounting clip, see page B1.22 ● UL Listed for use in plenum or air handling spaces per NEC

Preformed Clamping Systems Wide choice of sizes and materials in a leak resistant design. • • Smooth I.D. Clamps reduce the risk of leaks especially when used on thin walled hoses • • Vibration resistant lip lock design. No hammering or crimping • • Unique buckle nest and smooth ID design reduces leak paths • • Double wrapped steel bands for additional strength • • Various materials for corrosive environments • • Band widths - 1/4", 3/8", 1/2", 5/8" and 3/4" • • Available for hose assemblies up to 9" outside diameter

Set-screw couplings – steel – zinc plated

●● For indoor use ●● Versatile cable ties can be used in countless applications ●● One-piece construction for consistent performance and reliability ●● Among the lowest threading force of any one-piece cable tie in the industry ●● Curved tip is easy to pick up from flat surfaces and allows faster initial threading to speed installation ●● A variety of materials and colors available for specific applications ●● UL Listed for use in plenum or air handling spaces per NEC except PLT.6SM and PLT5H/6H/8H/13H

Combined Type 1, 2 and 3 tested protector (to BS EN 61643) for use on the main distribution board directly feeding electronic equipment such as computers, communication and control equipment, particularly where a structural Lightning Protection System (LPS) is employed. For use at boundaries up to LPZ 0 to protect against flashover (typically the main distribution board location) through to LPZ 3 to protect sensitive electronic equipment.

Combined Type 1, 2 and 3 tested protector (to BS EN 61643) for use on single phase mains power distribution systems primarily to protect connected electronic equipment from transient overvoltages on the mains supply, e.g. computer, communications or control equipment. For use at boundaries up to LPZ 0 to protect against flashover (typically the main distribution board location, with multiple metallic services entering) through to LPZ 3 to protect sensitive electronic equipment.

Combined Type 1, 2 and 3 tested protector (to BS EN 61643) for use on three phase mains power distribution systems primarily to protect connected electronic equipment from transient overvoltages on the mains supply, e.g. computer, communications or control equipment. Innovative remote display options allow both protector and display to be mounted in their optimum position. For use at boundaries up to LPZ 0 to protect against flashover (typically the main distribution board location, with multiple metallic services entering) through to LPZ 3 to protect sensitive electronic equipment

Features & benefits • Very low let-through voltage (enhanced protection to IEC/ BS EN 62305) between phase and neutral conductors, where sensitive equipment is connected • Full Mode design capable of handling partial lightning currents as well as allowing continual operation of protected equipment • Repeated protection in lightning intense environments • Innovative multiple thermal disconnect technology for safe disconnection from faulty or abnormal supplies (without compromising protective performance) • Three way visual indication of protection status and advanced pre-failure warning so you need never be unprotected

Features & benefits • Enhanced protection (to IEC/BS EN 62305) offering low let-through voltage further minimizing the risk of flashover creating dangerous sparking or electric shock • Repeated protection in lightning intense environments • Pluggable module design (with anti-vibration locking clip) allows for simple replacement at end-of-life • Compact, space saving design • Indicator shows when the SPD protection modules requires replacement • Remote signal contact can indicate the protector’s status through interfacing with a building management system

All Combinations of Copper, Aluminum, ACSR, AAAC, 5005, and Steel Tin-plated, high strength, copper alloy SERVIT® split-bolt with spacer. Spacer separates dissimilar conductors and provides long contact length that prevents high pressure point contacts between run and tap conductors. Use of PENETROX™ joint compound recommended with Aluminum and ACSR.

Compact, high strength, high copper alloy SERVIT® split-bolt has free-running threads and easy to grip wrench flats. Highly resistant to season cracking and corrosion, the SERVIT® provides maximum pressure and assures a secure connection on all combinations of run and tap conductors. Type KS-3 accommodates 3 maximum size conductors

Features and benefits: • Concrete tight when taped • Fire Alarm (FA) painted red for fire alarm identification